Appendix D.Remote Module Command Structure
|
Command |
Function |
Syntax |
Return Value |
|
0 |
Take VA Reading |
0 |
(+/-)##### |
|
1 |
Take VB Reading |
1 |
(+/-)##### |
|
2 |
Take Battery Reading |
2 |
<Sp><Sp>+#.# |
|
3 |
Take -12v Reading1 |
3 |
<Sp>-12.0 |
|
4 |
Firmware Version4 |
4 |
Ver#.# |
|
5 |
(See Note 2) |
5 |
<Cr> |
|
6 |
(See Note 2) |
6 |
000<Sp><Sp><Sp> |
|
7 |
Take +12v Reading1 |
7 |
<Sp>+12.0 |
|
8 |
Take +5v Reference Reading |
8 |
<Sp><Sp>+#.# |
|
9 |
Take 3.3v Reading1 |
9 |
<Sp><Sp>+3.3 |
|
D |
Load Probe Defaults3 |
D |
See Example D |
|
G |
Display Gauge Parameters3 |
G |
See Example G2 |
|
G |
Enter Gauge Parameters3 |
G70a/(Lorp)/#/#/# |
See Example G1 |
|
T |
Probe Temperature (°C)3 |
T |
(+/-)##.#### |
|
V |
Firmware Version (Remote Module)3 |
V |
Ver #.# |
|
# |
Display Probe Serial #3 |
# |
See Example # |
|
#sn |
Enter Probe Serial #3 |
#sn (16 Alphanumeric Characters Or Symbols) |
See Example #sn |
table 10: Remote Module Commands
Notes:
1 These commands exist only for GK-604 analog systems and are included in the digital system for compatibility.
2 Similar to Note 1, but are for internal use only.
3 These commands exist only for GK-604D digital system.
4 Firmware Version (Command 4) returns the Remote Module version for analog systems and the probe firmware version for digital systems.
Example 1: LOAD PROBE DEFAULTS
Loads probe default gauge parameters (calibration factors):
Command: D<CR>
Response: GT:70A ZR:0.0000 GF:1.0000 GO:0.0000 GT:70B ZR:0.0000 GF:1.0000 GO:0.0000
Channels VA and VB: Linear Conversion
Zero Read Offset = 0
Gauge Factor = 1
Gauge Offset = 0
Results in digits display = 2500(Vout)
Example 2: ENTER GAUGE PARAMETERS
Enter and store gauge parameters for each axis:
A-axis: Linear conversion
Zero Read Offset = 0
Gauge Factor = .62
Gauge Offset = 0
Command: G70A/L/0/.62/0<CR>
Response: GT:70A ZR:0.0000 GF:0.6200 GO:0.0000 GT:70B ZR:0.0000 GF:1.0000 GO:0.0000
B-axis: Linear conversion
Zero Read Offset = 0
Gauge Factor = 1.005
Gauge Offset = 0
Command: G70B/L/0/1.005/0<CR>
Response: GT:70A ZR:0.0000 GF:0.6200 GO:0.0000 GT:70B ZR:0.0000 GF:1.005 GO:0.0000
Example 3: DISPLAY GAUGE PARAMETERS
Display gauge parameters stored in the probe:
Command: G<CR>
Response: GT:70A ZR:0.0000 GF:0.6200 GO:0.0000 GT:70B ZR:0.0000 GF:1.005 GO:0.0000
Example 4: DISPLAY PROBE SERIAL NUMBER
Display the serial number that is stored in the probe:
Command: #<CR>
Response: 6001-E,126543
Example 5: ENTER PROBE SERIAL NUMBER
Note: The GK-604D IRA uses the serial number to determine the inclinometer probe units (metric or English) by reading the model number portion of the serial number string (the part to the left of the comma). If the model number does not contain an "-E" or a "–M" then unpredictable results may occur.
Enter and store probe serial number:
(Up to 16 alphanumeric characters and symbols may be stored.)
Command: #sn6001-E,126543<CR>
Response: 6001-E,126543